View EPE6338S_4478212.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Miniature 10 Base-T Isolation Transformer with Center Taps
ELECTRONICS INC.
EPE6338S
* Optimized for Level One LXT905 * * Robust design allows for toughest soldering processes * * Small outline package on 0.050" pitch 16 pin SOIC * * Complies with or exceeds IEEE 802.3, 10 Base-T Requirements * * Operating temperature : -40C to +85C * Electrical Parameters @ 25 C
Cable Side Inductance (H Min.) @ 100 KHz, 0.1 Vrms Xmit 200 Rcv 200
Interwinding Capacitance (pF Max.) @ 100 KHz, 0.1 Vrms 12
Leakage Inductance (H Max.) @ 100 KHz, 0.1 Vrms 0.3
Return Loss (dB Min.) 5-10 MHz
Hipot (Vrms)
Transceiver Side DCR ( Max.)
-20
1500
Xmit 0.35
Rcv 0.50
Schematic
Transmit 6 Transceiver Side 7 8 1:2 11 10 9 Cable Side 1 Transceiver 2 Side 3 Receive 1:1 16 15 14 Cable Side
Package
A (J) P N Dim.
Dimensions
(Inches) Min. Max. Nom. .480 .260 .180 .350 .005 .050 .370 .016 .010 .070 0 .025 .500 .280 .200 Typ. .015 Typ. .390 .022 Typ. Typ. 8 .045 (millimeters) Min. Max. Nom. 12.19 6.60 4.57 8.89 .127 1.27 9.40 .406 .254 1.78 0 .635 12.70 7.11 5.08 Typ. .381 Typ. 9.91 .559 Typ. Typ. 8 1.14 .762 1.27 1.40 10.41
PCA EPE6338S Date Code
B
Suggested Solder Pad Layout
Q
D
M
C
E
K
I
H
F
L G
A B C D E F G H I (J) K L M N P Q
.030 .050 .055 .410
PCA ELECTRONICS, INC 16799 SCHOENBORN ST. NORTH HILLS, CA 91343
CSE6338Sa Rev. -
9/1/98
Product performance is limited to specified parameters. Data is subject to change without prior notice.
TEL: (818) 892-0761 FAX: (818) 894-5791 http://www.pcainc.com
Miniature10 Base-T Isolation Transformer with Center Taps
ELECTRONICS INC.
EPE6338S
The circuit below is a guideline for interconnecting PCA's EPE6338S with LXT905 10 Base-T PHY chip over UTP cable. Further details of system design, such as chip pin-out, etc. can be obtained from the specific chip manufacturer. Typical insertion loss of the isolation transformer is 0.7dB. This parameter covers the entire spectrum of the encoded signals in 10 Base-T protocols. However, the predistortion resistor network introduces some loss which has to be taken into account in determining how well your design meets the Standard Template requirements. Additionally, the following need to be considered while selecting resistor values : a. Each channel needs 100 termination, thus the Thevenin's equivalent resistance seen by a channel looking into the transmit outputs from the chip must be equal to a value close to 100. The LXT 905 driver output impedances are very low. . Thus only 11.8 on TPON & TPOP are enough to provide a balanced 25 termination given that turns ratio is 1:2. Following these guidelines will guarantee that the return loss specifications are satisfied at all extremes of cable impedance (i.e. 85 to 115) while the module is installed in your system. The receiver channel termination is rather straight forward: two 50 loads provide the balanced termination to the cable. b. That the template requirements are satisfied under the worst case Vcc (i.e. 4.5V), will impose a further constraint on resistor selection, in that they ought to be the minimum derived from the calculations. Users can allow for pads on their PCB for a shunting resistor across pins 6 and 8 of EPE6338S for more flexibility in setting voltage levels at the outputs. Note that some systems have auto polarity detection and some do not. If not, be certain to follow the proper polarity. The pulldown resistors used around the RJ45 connector have been known to suppress unwanted radiation that unused wires pick up from the immediate environment. Their placement and use are to be considered carefully before a design is finalized. It is recommended that there be a neat separation of ground planes in the layout. It is generally accepted practice to limit the plane off at least 0.08 inches away from the chip side pins of EPE6338S. There need not be any ground plane beyond this point. For best results, PCB designer should design the outgoing traces preferably to be 50, balanced and well coupled to achieve minimum radiation from these traces.
Typical Application Circuit for UTP with external Resistor Network
TPIN
50
1 2
9 11
1 2 3 6
TX+ TX-
RJ45*
RX+ RX4 5 7 8
EPE6338S
50
14 16
LXT905 PHY
TPIP TPON
11.8
3 6 8 10
15
11.8
HV Cap
TPOP .1uF X7R
100pF
100pF
High voltage cap, if used 2KV recommended Chassis Ground
Notes : * Pin-outs shown are for NIC configurations. For Hubs and Repeaters swap pins 1-2 with pins 3-6.
PCA ELECTRONICS, INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343
CSE6338Sb Rev. -
9/1/98
TEL: (818) 892-0761 FAX: (818) 894-5791 http://www.pcainc.com

▲Up To Search▲

Price & Availability of EPE6338S

	To Download EPE6338S Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .